How to Remove Garbage Disposal and Replace with Pipes?

Are you tired of dealing with a garbage disposal? If so, it may be time to remove your existing disposal and replace it with pipes. This is not as difficult a task as it may seem at first. With the right tools and materials, you can remove your current garbage disposal and install new pipes in no time.

In this guide, we will walk you through the steps for removing your garbage disposal and replacing it with pipes. We’ll also provide some tips on how to make sure that everything is installed correctly for optimal performance. So let’s get started!

Preparation before Removing the Garbage Disposal

Before you remove the existing garbage disposal, you will need to shut off the power source. This can be done by cutting off a circuit breaker or unplugging the disposal from the wall outlet. If there is any water remaining in the sink, remove it using a bucket or other container.

Uninstalling the Garbage Disposal

Step 1: Unscrew the Screws

Once you have shut off the power source, remove the mounting screws that hold the disposal in place. These screws can usually be found at the bottom of the unit or on either side of it. Gently pull out the unit and remove any debris from inside it. If there are any old pipes or fittings attached to the disposal, remove them as well.

Step 2: Remove the Pipes

Now it’s time to remove the pipes from underneath the sink. This will involve disconnecting them from both sides and unscrewing any clamps that are holding them in place. Once everything is disconnected, remove all of the old pipes from the sink.

Step 3: Remove the Garbage Disposal Unit

Finally, remove the garbage disposal unit from the sink. This should be easy to do since it was already disconnected from the power source and pipes in Step 1 and 2. Once you have removed the unit, make sure to discard it properly according to local guidelines.

Step 4: Clean the Sink Area

Once all of the old pipes have been removed, it’s time to clean up the area. Use a rag or brush to remove any dirt and debris from underneath the sink. This will help ensure that your new pipes get installed correctly.

Installing New Pipes and Drains

Now that all of the old pipes have been removed, you can begin to install the new ones. Start by inserting one end of each pipe into its respective fitting. Make sure that they are as secure as possible and use clamps or locking nuts to keep them in place.

Once you have connected all of the pipes, you can attach the drain to the sink. This is usually done using a rubber gasket and locking nut. Make sure that everything is tight and secure before moving on to the next step.

Connecting Water Lines to the Sink Drain Pipe

Then, connect the water lines to your sink drain pipe. This will usually involve connecting a flexible hose from the drain to the main water line. Make sure that this connection is tight and secure so that you don’t have any leaks.

Once everything is connected, turn on the water and check for any leaks or issues.

Securing All Connections with Plumbing Tape and Clamps

Finally, make sure to secure all of the connections with plumbing tape and clamps. This will help ensure that everything is sealed tightly and won’t leak when you turn on the water. Once this step is completed, your new pipes should be ready for use!

To secure all parts are well connected, you can use a wrench or adjustable pliers to remove the nuts and bolts. This will help ensure that your new pipes remain in place for years to come.

Testing Your Work and Finishing Up

Once all the connections have been secured, it’s time to test your work. Turn on the water and make sure that there are no leaks or issues with the new pipes. If everything looks good, you can remove any excess materials and clean up the area. Then all that’s left is to turn on the power source and enjoy your newly installed pipes!

For a straightforward installation, you can also check the video:


Removing garbage disposal and replacing with pipes is a straightforward task that requires patience and careful attention to detail. While it might seem intimidating at first, following these steps will help ensure that you remove and reinstall your garbage disposal without any issues.

With the right tools and materials, you can remove your existing garbage disposal and install new pipes in no time. Make sure to follow all of the instructions carefully and securely connect all of the components so that everything runs smoothly.

Now you can enjoy a clean, functioning sink without any trouble. If you experience any issues with your installation or have any questions while carrying out this project, contact us directly, or be sure to reach out to a qualified professional for help. Good luck!